By Plumbing Guide for Bathtub Installation
By Plumbing Guide for Bathtub Installation
Blog Article
Here below you will discover more professional ideas in relation to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably tough project. If the old bathtub is easily available, the project can move immediately; if you need to open a wall to get rid of the old tub as well as position the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the new one. See to it you have actually qualified on your own for the job and also fit attempting it. Instead of working with a contractor to take control of a halfway-completed job, it is much better to think about utilizing one prior to you start. Chances are you may require a specialist plumber to make tube links.
This write-up will aid you mount a new tub in your shower room if you have actually currently acquired a brand-new tub as well as don't need to transform the plan of your previous supply of water pipelines.
Your tools as well as material checklist ought to make up the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is detach the water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of eliminating the existing taps can be rather troublesome as a result of the limited accessibility that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before moving on to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the tap as well as the sink. Safeguard the faucet in place with the supplier offered backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bathtub
Making use of the two wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are practical in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bath tub up until the level reads degree.
To install taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the water system and also inspect all joints as well as brand-new pipework for leakages and also tighten them if needed. Fill the tub as well as additionally inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the maker's user's manual. Tiling and also sealing around the bathtub needs to wait until the bath tub has actually been used at least when as this will certainly settle it right into its last placement.
Getting ready for the Installation
To start with, the supporting framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to avoid strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, bring about difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill the tub with water before sealing, to enable the activity experienced when the tub remains in usage. The sealer can fracture relatively early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is suggested to fit the ceramic tiles utilizing waterproof or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that report on Tools You Need to Install a New Bathtub from an acquaintance on our other web property. Enjoyed reading our posting? Please share it. Let another person locate it. I cherish reading our article about How to Install a Bathtub Yourself.
Plumbing emergencies? Our experts await. Report this page